Name: Hantek DSO2000 Series
SKU: 5336
Availability: BackOrder

Feature：

2 channels which are respectively controlled by independent knobs
100 MHZ and 150MHZ analog channel bandwidth
Sampling rate up to 1 GSa/s
8M memory depth
Vertical range 2mV/div ~ 10V/div
Built-in 1 CH 25MHz waveform generator (DSO2D10, DSO2D15)
Vertical resolution: 8bit
Trigger: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
BUS decode and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN
Can save multiple data formats, such as settings, waveforms, reference waveforms, CSV, pictures
A 3-digit digital voltage meter and a 6-digit hardware frequency indicator
32 kinds of auto measurements with statistics, real-time statistics of maximum, minimum, standard deviation and etc.
2 sets of digital voltmeters
Support threshold testing, free measurements within the screen
Abundant SCPI remote command control
USB Host/Device.

Parameters

Model	DSO2D15	DSO2D10	DSO2C15	DSO2C10
Bandwidth	150MHz	100MHz	150MHz	100MHz
Oscilloscope channels	2CH	2CH	2CH	2CH
Waveform generator	1CH	1CH	–	–
Oscilloscope
Sample rate	1GSa/s (single channel) 500MSa/s (two channels)
Acquisition
Normal	Sample data
Peak-to-peak value	Display high frequency and random burr
Average	Average waveform, times: 4, 8, 16, 32, 64, 128
High resolution	Up to 12bit
Input
Input coupling	DC, AC, GND
Input impedance	1MΩ±2% ‖20pF±3pF
Probe attenuation factor	1X, 10X, 100X, 1000X
Voltage rating	300V CAT II
Maximum input voltage	300VRMS (10X)
Horizontal
Waveform interpolation	(sin x)/x
Maximum record length	Single channel maximum 8M
	Two channels maximum 4M
Horizontal scale range	2ns/div~100s/div 1, 2, 5 step by step
Time base mode	Y-T, X-Y, Roll
Zero offset	±0.5 div×minimum time base gear
Sample Rate and Delay Time Accuracy	±25ppm
Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy	single-shot, Normal mode ±（1 sample interval+100ppm×reading+0.6ns）
					＞16 times averages ±（1 sample interval+100ppm×reading+0.4ns）
	Sample interval=sec/div÷200
	Sample Rate and Delay Time Accuracy	±50ppm（at any interval greater than 1ms）
	Vertical
Model	DSO2D15	DSO2D10	DSO2C15	DSO2C10
Bandwidth	150MHz	100MHz	150MHz	100MHz
Rising time in BNC position (typical)	2.4ns	3.5ns	2.4ns	3.5ns
Vertical resolution	8 bits resolution, each channel samples simultaneously
Vertical sensitivity	2mV/div to 10V/div
Offset range	≥ 200mV/div, ±1V;
	＜200mV/div ±50V
Mathematical operation	+, -, ×, ÷, FFT
FFT	Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop
Bandwidth Limit	20MHz
Bass response（-3db）	In BNC position ≤ 10Hz
Vertical gain accuracy	In ”normal” or ”average” acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%;
	In ”normal” or ”average” acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4%
Note: Bandwidth reduced to 6MHz when using a 1X probe
Trigger
Trigger type	Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC
Trigger level range	±5 divisions from the center of the screen
Trigger mode	Auto, Normal, single
Level	CH1~CH2	±4 divisions from the center of the screen
	EXT(Only With AWG Model)	0~3.3V
Holdoff range	8ns~10s
Trigger level accuracy	CH1~CH2	0.2 div×volts/div within ±4 divisions from the center of the screen
	EXT(Only With AWG Model)	±（Set value× 6%+40mV）
Edge trigger	Slope	Rising edge, falling edge, rising or falling edge
	Signal source	CH1, CH2, EXT(Only With AWG Model)
Pulse width trigger	Polarity	Positive polarity, negative polarity
	Condition(When)	<, >, !=, =
	Signal source	CH1~CH2,
	Pulse width range	8ns ~ 10s
	Accuracy	8ns
Video trigger	Signal standard	NTSC, PAL
	Signal source	CH1~CH2
	Synchronization	Scanning line, line number, odd field, even field, all field
Slope trigger	Slope	rising, falling
	Condition(When)	<, >, !=, =
	Signal source	CH1 ~ CH2
	Time range	8ns ~ 10s
	Accuracy	8ns
Overtime trigger	Signal source	CH1~CH2，
	Polarity	Positive polarity, negative polarity
	Time range	8ns ~ 10s
	Accuracy	8ns
Window trigger	Signal source	CH1~CH2
Pattern trigger	Pattern	0: low level; 1: high level; X: ignore
	Level（signal source）	CH1~CH2
Interval trigger	Slope	rising, falling
	Condition(When)	<, >, !=, =
	Signal source	CH1~CH2
	Time range	8ns ~ 10s
	Accuracy	8ns
Under Amp trigger	Polarity	Positive polarity, negative polarity
	Condition(When)	<, >, !=, =
	Signal source	CH1~CH2
	Time range	8ns ~ 10s
	Accuracy	8ns
UART trigger	Condition(When)	Start, Stop, data, Parity ERR, COM ERR
	Signal source(RX/TX)	CH1~CH2
	Data format	Hex (hexadecimal)
	Data length	1 byte
	Data bit width	5 bit, 6 bit, 7 bit, 8 bit
	Odd-even check	none, odd, even
	Idle level	high, low
	Baud rate (optional)	110 / 300 / 600 / 1200 / 2400 / 4800 / 9600 / 14400 / 19200 / 38400 / 57600 / 115200 / 230400 / 380400 / 460400 bit/s
	Baud rate(user-defined)	300bit/s~334000bit/s
LIN trigger	Condition(When)	Interval field, synchronization field, ID field, synchronization error, identifier, ID and data
	Signal source	CH1~CH2
	Data format	Hex (hexadecimal)
	Baud rate (optional)	110 / 300 / 600 / 1200 / 2400 / 4800 / 9600 / 14400 / 19200 / 38400 / 57600 / 115200 / 230400 / 380400 / 460400 bit/s
	Baud rate(user-defined)	300bit/s~334000bit/s
CAN trigger	Condition(When)	Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame
	Signal source	CH1~CH2
	Data format	Hex (hexadecimal)
	Baud rate (optional)	10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000
	Baud rate(user-defined)	5kbit/s~1Mbit/s
SPI trigger	Signal source	CH1~CH2
	Data format	Hex (hexadecimal)
	Data bit width	4, 8, 16, 24, 32
IIC trigger	Signal source (SDA/SCL)	CH1~CH2
	Data format	Hex (hexadecimal)
	Data index	0~7
	When(condition)	Start bit, stop bit, No Ack, address, restart, address and data
Measurement
Cursor	Voltage difference between cursors △V
	Time difference between cursors △T
	Reciprocal of △T, in Hertz (1/△T)
Auto measurement	frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, – width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, – duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF
					DVM	Data source	CH1, CH2
Measurement type	DC RMS
	AC RMS
	DC
Frequency meter	hardware 6 bits frequency meter
Arbitrary waveform generator
Channel	1
Sample rate	200MSa/s
Vertical resolution	12 bits
Maximum frequency	25 MHz
Standard waveforms	sine, square, ramp,Exp, noise, DC
					Arbitrary waveform	Arb1, Arb2, Arb3, Arb4
Sin	Frequency range	0.1Hz~25MHz
Square/pulse	Frequency range	0.1Hz~10MHz
Triangular wave	Frequency range	0.1Hz~1MHz
Sampling wave	Frequency range	0.1Hz~1MHz
Index	Frequency range	0.1Hz~5MHz
Noise
Arb1	Frequency range	0.1 Hz to 10 MHz
Arb2	Frequency range	0.1 Hz to 10 MHz
Arb3	Frequency range	0.1 Hz to 10 MHz
Arb4	Frequency range	0.1 Hz to 10 MHz
Waveform length	4KSa
Frequency	Accuracy	100 ppm (<10 kHz) 50 ppm (>10 kHz)
	Resolution	0.1 Hz or 4 bits，take the greater one
Amplitude	Output range	10mV~7Vp-p (high impedance)
		5mV~3.5Vp-p (50Ω)
DC offset	Range	±3.5 V, high impedance
		±1.75 V, 50 Ω
	Resolution	100 μV or 3 bits, take the greater one
	Accuracy	2% (1 kHz)
Output impedance	50 Ω
General specifications
Display	Display type	7” diagonal TFT liquid crystal
	Display resolution	800 (horizontal)*480 (vertical) pixels
	Display colour	16 million colours (24 bits true colour)
	Persistence time	minimum, 1 s, 5 s, 10 s, 30 s, infinite
	Display type	dot, vector
	Display brightness	adjustable
	Grid type	adjustable
	Grid brightness	adjustable
Interface	Standard interface	USB Host，USB Device
General specifications	Probe compensator output
	Output voltage, typical	about 2Vpp input ≥1MΩ load
	Frequency, typical	1kHz
	Power supply	100-120VAC_RMS(±10%), 45Hzto 440Hz, CATⅡ
		120-240VAC_RMS(±10%), 45Hz to 66Hz, CATⅡ
	Power consumption	<30W
	Fuse	T, 3.15A, 250V, 5x20mm
	Operating temperature	0~50 °C (32~122 °F)
	Storage temperature	-40~+71 °C (-40~159.8 °F)
	Humidity	≤+104℉(≤+40°C): ≤90% relative humidity
		106℉~122℉ (+41°C ~50°C): ≤60% relative humidity
	Altitude	Operating and nonoperating	3, 000m (10, 000 feet)
	Mechanical shock	Random vibration	0.31 g_RMSfrom 50Hz to 500Hz,
			10 minutes on each axis
		Nonoperating	2.46g_RMS from 5Hz to 500Hz,
			10 minutes on each axis
		Operating	50g, 11ms, half-sine wave
	Mechanical	Size	318 x 110 x 150mm (length x width x height)
		Weight	1900g

GPIO Modules

Relay Modules

FPGA & ACCELERATED COMPUTING

Tested Measurement

Shop

Hantek DSO2000 Series

Parameters

Reviews

USB TO RS485/422

USB TO 4CH RS232485

USB TO RS232/485

Analog Discovery 2

Phone:

Email:

Address:

Shop

Hantek DSO2000 Series

Parameters

Reviews

Related products

Phone:

Email:

Address: